ɧ»¢ÊÓƵ Internet Gateway \u002D Activate \/ Set Up Device<\/div><\/h1>

Here\x27s how to assemble and activate the Internet Gateway.<\/div><\/div>

Inside the box:

Setup guide<\/div><\/li>

ɧ»¢ÊÓƵ Internet Gateway (ARC\u002DXCI55AX)<\/div><\/li>

Power adapter<\/div><\/li>

Ethernet cable<\/div><\/li><\/div><\/ul><\/div><\/div> <\/div><\/section><\/div>

Out of Box Setup<\/div><\/h2>

Remove the Gateway from the box.<\/div><\/span><\/div><\/li>

Place the Gateway on a stable surface near a window.<\/div><\/span><\/div><\/li>

Connect the power adapter to the Gateway and plug it into a power outlet.<\/div><\/span>

The Gateway’s blinking white light means it’s starting up. The light may fluctuate between red and white for up to 5 minutes; don’t unplug the Gateway. If the light turns solid red, move the Gateway to a different location and try again or get help in the My ɧ»¢ÊÓƵ app via the info below.<\/div><\/div> <\/div><\/div><\/div><\/li>

Check for a solid white light on the Gateway.<\/div><\/span>

It can take up to 5 minutes to appear. Once the Gateway shows a solid white, setup is complete.<\/div><\/div> <\/div><\/div><\/div><\/li>

Connect your devices to your new Wi\u002DFi network.<\/div><\/span>

Use the Wi\u002DFi name and password printed on the bottom of the Gateway to connect your devices. Or scan the QR code printed there to connect automatically. You can edit your Wi\u002DFi name and password in My ɧ»¢ÊÓƵ app.<\/div><\/div>

<\/div><\/div><\/div><\/div><\/li><\/div><\/ol><\/div> <\/div> <\/div> <\/div>

Advanced Setup via My ɧ»¢ÊÓƵ app<\/div><\/h2>

Using a mobile device, open the camera and scan the QR code located on top of the toolkit box found inside the router box.<\/div><\/span>
If you\x27re unable to scan the QR code, open a browser on your mobile device and navigate to the
http:\/\/setup.verizon.com\/verizoninternetgateway<\/div><\/span> website.<\/div><\/div> <\/div><\/div><\/div><\/li>
Tap
Start 5G Home Internet setup<\/div><\/span> to get started.<\/div><\/span><\/div><\/li>
From the \x27Welcome to 5G Home Internet\x27 screen, tap
Watch video<\/div><\/span>.<\/div><\/span><\/div><\/li>
From the \x27Let\x27s get started\x27 screen, tap
Continue<\/div><\/span>.<\/div><\/span><\/div><\/li>
Remove the router and AC adapter from the box then tap
Continue<\/div><\/span>.<\/div><\/span><\/div><\/li>
Review the \x27Tips to set up the Gateway\x27 then tap
Got it<\/div><\/span>.<\/div><\/span>
Make sure it\x27s near a window on or above the ground floor.<\/div><\/span>
Avoid windows in the basement.<\/div><\/div> <\/div><\/div><\/div><\/li>
Make sure it\x27s elevated.<\/div><\/span>
Place it on an elevated surface to allow the signal to transmit to every area of your home. This allows the signal to transmit to every area of your home.<\/div><\/div> <\/div><\/div><\/div><\/li>
Clear away any objects to close to the window.<\/div><\/span>
Clutter could interfere with the Gateway getting a signal.<\/div><\/div> <\/div><\/div><\/div><\/li><\/div><\/ol><\/div><\/li>
Place the router on an elevated surface near a window or exterior\u002Dfacing wall then tap
Continue<\/div><\/span>.<\/div><\/span><\/div><\/li>
Connect the AC adapter to the router and plug it into an outlet. You will see a white blinking light for about 5 minutes. Tap
Continue<\/div><\/span> when the light stops blinking.<\/div><\/span><\/div><\/li>
Wait 5 minutes until you see a solid white light then from the screen prompt, tap
Solid white light<\/div><\/span>.<\/div><\/span>
If you see a solid red light, the Gateway has found a weak signal. Tap
Use 5G compass<\/div><\/span> then follow the on\u002Dscreen prompts or watch this 5G compass video<\/a> for more info. This option is only available for 5G Home Plans.<\/div><\/div><\/div><\/div>
If you see a blinking white light, the device may be updating firmware. Wait for about 5 minutes until you see a solid white light.<\/div><\/div>
For more info on LED indicators, refer to LED Status Indicators<\/a>.<\/div><\/div> <\/div><\/div><\/div><\/li>
Once you click on Solid white light, tap
Continue<\/div><\/span> after the following screens display: Communicating with the Gateway > Checking your connection > Connecting to the internet > You found a strong signal. <\/div><\/span><\/div><\/li>
Connect to Wi\u002DFi either by scanning the QR code on the bottom of the Internet Gateway with your phone or by entering the Wi\u002DFi name and password on your device then tap
Continue<\/div><\/span>.
<\/div> <\/div><\/span><\/div><\/li>
From the \x27Success\x27 screen, tap
Manage network<\/div><\/span> to personalize your Wi\u002DFi name and password in Network settings, and more.<\/div><\/span>
A My ɧ»¢ÊÓƵ account is necessary to manage your device. Refer to Create Profile \/ Register for My ɧ»¢ÊÓƵ \u002D Website<\/a> for more info on registering for My ɧ»¢ÊÓƵ.<\/div><\/div> <\/div><\/div><\/div><\/li><\/div><\/ol><\/div> <\/div> <\/div> <\/div>
<\/div><\/h2>
<\/div>
Connect the Wireless Client Manually<\/div><\/span><\/a><\/div> <\/div>